Introduction:
D(TD)-Type vertical bucket elevator is composed by moving parts (hopper and traction tape), with the upper section of the drive roller, with the lower section of the idler pulley, intermediate casing, driving device, non-return brake, etc.
Features:
1. This machine is characterized by rapid centrifugal discharge
2. The rubber conveyor belt is used as a traction component, so it is not suitable for conveying large pieces of materials with high grinding and cutting resistance.
3. The temperature of the material to be transported shall not exceed 60 ° c. 150 ° c is allowed if the heat-resistant rubber belt is used.
4. The conveying capacity of the machine is 3.1~66 cubic meters per hour and the height is 4~30 meters.
Applications:
suitable for the upward transportation powder, granular, small block of no cut sex or half grinding cut, loose materials such as coal, sand, dust coke, cement, mineral water, etc.
manufacturing and installation methods:
In order to meet various requirements, the machine has a variety of manufacturing and installation methods.
1. According to the shape of hopper, it is divided into two types
S method — with deep garden bottom hopper
Q method — with shallow garden bottom hopper
2. There are two types of discharge ports in the upper section
X1 method — discharge port with inclined flange
X2 method — discharge port with horizontal flange
3, according to the lower section of the form of the feed port is divided into two
J1 method — the inclined plane of the feed inlet forms a 45 Angle with the horizontal plane
J2 method — the inclined plane of the feed inlet forms a 60 Angle with the horizontal plane
4. According to the position of the side inspection door in the middle housing, it is divided into four types
K1 method — middle housing side with lower left inspection door
K2 method — middle housing side with lower right inspection door
K3 process – middle housing side with upper left inspection door
K4 process – middle housing side with upper right inspection door
5. According to the position of the inspection door on the end face of the middle housing, it is divided into two types
Z1 method — middle housing end face with bottom inspection door
Z2 method — middle housing end face with upper inspection door
6, according to the transmission of the relative position of the elevator is divided into two
Left – the drive is on the left
Right – the drive is on the right
Project |
Hoist Type |
|||||||
D160 |
D250 |
D350 |
D450 |
|||||
S Making Method |
〇 Making Method |
S Making Method |
〇 Making Method |
S Making Method |
〇 Making Method |
S Making Method |
Q Making Method |
|
Transport Capacity(m³/h ) |
8 |
3.1 |
21.6 |
11.8 |
42 |
25 |
69.5 |
48 |
Hopper Capacity(L ) |
1.1 |
0.65 |
3.2 |
2.6 |
7.8 |
7 |
15 |
14.5 |
Bucket Pitch(mm ) |
300 |
300 |
400 |
400 |
500 |
500 |
640 |
640 |
Tape Weight With Hopper(kg/m ) |
4.72 |
8.8 |
10.2 |
9.4 |
12.1 |
12.1 |
21.3 |
21.3 |
Conveyor Tape: width(mm) |
200 |
300 |
400 |
500 |
||||
Conveyor Tape: number of layers |
4 |
4 |
5 |
5 |
||||
Hopper Speed(m/s ) |
1 |
1.25 |
1.25 |
1.25 |
||||
Rotation Of Transmission Drum Shaft(r/min ) |
47.5 |
47.5 |
47.5 |
37.5 |
||||
Maximum Bulk Of Material(mm) |
25 |
35 |
45 |
55 |